ventoyzas29

Forum Replies Created

Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • in reply to: CR10 PROFILE #62953
    Avatarventoyzas29
    Participant

    and here are some of my prints

    in reply to: CR10 PROFILE #62947
    Avatarventoyzas29
    Participant

    i use cr-10 and s3d for a long time with no problem…..
    as all the printers need deferend tuning i give a start point for a good print
    you can use the s3d factory files you open it and then you must change
    Retraction Distance from 0.8 to 5.8mm
    retraction speed from 30 to 60 mm
    this is the most crusial part you mast change now the temperature is up to you and the layer height
    just you mast know the cr-10 step motors they have 0.04 mm per step sho the 0.25mm layer height is not good..
    for big parts i change it to 0.26 and for smaller one i use 2.4
    maybe you going to need a litle more extra restart distance u can start from the factory 0.12 and if you see gaps in the prints you must increase it…. i use 0.18 in my printer ….
    as i say this is a starting point still maybe you need somthing more all the cr-10 are not the same…… if you have any other problem post the problem i can give a advice if i can……
    greatings from greece

    in reply to: Larger edge 540 #29104
    Avatarventoyzas29
    Participant

    i have print one at 165% with wingspan 1.98m if i remember correct..
    i have use a carbon rod in the wings and paint it and it fly perfect

    in reply to: Problem with CR 10 #21134
    Avatarventoyzas29
    Participant

    the retraction is to low
    use retraction distance 5.5 mm
    and retraction speed arount 60 mm/s
    and lower the first layer height meybe 90% or 95%

    in reply to: my cessna 152 #20421
    Avatarventoyzas29
    Participant

    i have a hard time to upload the images show i try a other one

    • This reply was modified 2 years, 2 months ago by Avatarventoyzas29.
    • This reply was modified 2 years, 2 months ago by Avatarventoyzas29.
    in reply to: Your Printer Setting #19368
    Avatarventoyzas29
    Participant

    and very important that i forgot to mention
    on the cura go to settings then setting visibility
    on the travel section
    check for combine mode and after set it to off….
    only from this you lose a lot of stinging…..

    in reply to: Your Printer Setting #19359
    Avatarventoyzas29
    Participant

    printer = cr-10
    slicer = cura 2.7 (for now )
    plane = cessna 152 (amazing plane) thks a lot stepan
    i have try to print it for a week now
    first print was like this
    fist tests

    then i play a lot for the setting i allmost change anithing and make test prints
    and after a lot of setups and test print i finaly can print as i want it (allmost :P)
    nice
    smooth

    my setting for wings and fuselage are
    settings
    setup

    with this settings i get allmost zero stinging and excelent adhesion (i print 3 wing parts together with no build plate adhesion )
    the temp is not the same for all filaments
    after some tests i find beter to use temp +10 from the filament factory recomented temp… the pla tha i have now say temp. print 200-220c show i setup the temp to 230c
    wen i finish the print i have now, i try to lower a litle the retraction speed (maybe 45-50)

    i have not start printing the landing gears – flaps – aileron etc wen i print them with good resulds i post my settings

    any recoment welcome
    im still new to this and still learning
    i make a lot of bad prints and spent allmost 1 kg filament to make this setup and i hope help some of u guys to have faster good resulds….
    for any help msg im here to help if i can….
    after all we sare the same pasion for this hobby….
    and thank you again stepan the plane is amazing
    i m sorry for my english i try to do my best…..
    greetings from greece 🙂

    • This reply was modified 2 years, 3 months ago by Avatarventoyzas29.
    • This reply was modified 2 years, 3 months ago by Avatarventoyzas29.
    • This reply was modified 2 years, 3 months ago by Avatarventoyzas29.
    • This reply was modified 2 years, 3 months ago by Avatarventoyzas29.
    • This reply was modified 2 years, 3 months ago by Avatarventoyzas29.
    in reply to: CR-10 #19172
    Avatarventoyzas29
    Participant

    after a lot of tests i thing i manage to take a perfect print (cheers) 😛 from my cr-10
    i let it finish and wen i come from the work i make a post for helping…..

Viewing 8 posts - 1 through 8 (of 8 total)