NavPack D004

NavPack_D04_01
NavPack_D04_03
NavPack_D04_08
NavPack_D04_07
NavPack_D04_06
NavPack_D04_05
NavPack_D04_04
NavPack_D04_03
NavPack_D04_02
NavPack_D04_04
NavPack_D04_05
NavPack_D04_02
NavPack_D04_06
NavPack_D04_01
D22_pers_03
D22_front_01
D-20_18
D-20_11
D-18_08
D24_persp_01
signal-2026-05-16-232730_002
R6__7306

NavPack D004

Price range: $375.00 through $395.00

NavPack D04                                                                                                                                              

Complete Navigation & Power Core for Professional VTOL UAV

NavPack D04 is not just a flight controller — it is a complete navigation pack: autopilot, GNSS, professional magnetometer, digital pitot-static sensing 

and full power electronics on a single board. One assembled, tested unit instead of a box full of cables and five separate modules.                      

Just plug in motors and servos. No soldering, no wiring, no tears.

Product Description

NavPack D04

Complete Navigation & Power Core for Professional VTOL UAV

NavPack D04 is not just a flight controller — it is a complete navigation pack: autopilot, GNSS, professional magnetometer, digital pitot-static sensing and full power electronics on a single board. One assembled, tested unit instead of a box full of cables and five separate modules.

Just plug in motors and servos. No soldering, no wiring, no tears.

The easiest path to a VTOL aircraft — and a surprisingly affordable one. Price the parts separately — autopilot, GNSS, professional magnetometer, digital airspeed sensor, power monitor, three regulators, distribution board, plus all the cables — and the NavPack costs less than the shopping list. Instead of a box of modules you get one tested, calibrated, high-quality board, pre-flashed with a complete aircraft setup: you save money, time and a lot of headaches — and go flying.

NavPack vs. a classic DIY stack

What it takes to match the NavPack with off-the-shelf modules of comparable sensor quality (street prices, USD):

Function DIY stack (e.g. Matek) ~Price NavPack D04
Autopilot (STM32H743) Matek H743-WING V3 $130 on board
GNSS + RM3100 professional compass Matek M10-L4-3100 $89 on board
Digital airspeed + barometer (Amphenol AUAV combo) Matek ASPD-AUAV (airspeed only) $110 on board — AUAV: airspeed + baro, plus a second independent baro (dual-baro redundancy)
Precision power monitor Holybro PM02D $30 on board
Extra BEC (servo rail) assorted $10 3× 8 A regulators on board
Raspberry Pi / companion hookup — 5 V BEC + MAVLink wiring assorted $25 2×20 Pi header on board: plug in, autopilot-switched power (RELAY 1), MAVLink wired
Power distribution — 3× ESC, up to 12S PDB + wiring $15 on board (2× XT60, 5× XT30)
Connectors, cables, heat-shrink — $20 not needed
Total ~$429 $395 — incl. firmware & calibration

And the part no price tag shows — the work:

NavPack D04 Classic DIY stack
Soldering none hours — ESC power leads, XT60, BECs, PDB
Wiring plug in motors & servos 5–6 modules over UART/I2C/CAN, crimping
Firmware golden image pre-flashed flash & configure from scratch
Aircraft parameters complete D-20C setup pre-loaded universal param file + board-specific part yourself
Sensor calibration factory-calibrated, test protocol included all calibrations yourself
Autolaunch button yes not available
Battery input 3–12S, 2× XT60 pass-through typically 2–8S
Companion computer Pi plugs onto the board — mechanically secured, powered, relay-switched, MAVLink wired extra BEC, UART soldering, cable harness + you must design and build a mount for the Pi itself
Support one vendor, one board several vendors
Time to first flight ~1–2 hours a weekend or more

HIGHLIGHTS

  • STM32H743 autopilot running ArduPilot with a dedicated 3DFENSE hardware definition and the unique Autolaunch feature — start the whole mission with one button on the airframe, no laptop, no RC transmitter.
  • Full sensor suite on board — ICM-42688-P IMU, DPS368 barometer, RM3100 professional magnetometer, AUAV digital airspeed sensor, SAM-M10Q GNSS, INA228 power monitor, blackbox.
  • 16 actuator outputs — BDShot on ESC channels with per-motor RPM telemetry, dedicated servo rail up to 7.4 V.
  • 3× 8 A (10 A peak) buck regulators — separate rails for FC, servos and companion computer. Companion rail is switchable by the autopilot and at 7 V usable as a power source for a VTX or HD air unit.
  • Raspberry Pi GPIO-compatible header — a Pi or AI companion computer mounts directly, no cables: powered from its own dedicated 8 A rail switched by the autopilot (RELAY 1 — keep it off until the mission needs it, or power-cycle it in flight from the GCS, a mission or an RC switch; the auxiliary 5 V payload output is RELAY 2), with MAVLink telemetry already wired to the header. Part of the 3DFENSE ecosystem with the CM5 Extension Module (LTE, mesh radio, Starlink, Hailo-10H AI).
  • mLRS combo connector — one connector for RC and full MAVLink telemetry. ELRS, CRSF, SBUS and HD systems supported.
  • 3S–12S battery input — 2× XT60 pass-through.
  • 99 × 54 mm, 70 g — compact single-board footprint.

FIRMWARE — CHOOSE AT CHECKOUT

  • D-20C VTOL firmware/setup — board ships pre-flashed and tested with the aircraft-specific build for the D-20C Personal Eagle II: parameters, mixes, transition logic and Autolaunch pre-set, including a detailed step-by-step installation guide. More airframes to come.
  • Clear — no firmware (flash it yourself) — the same assembled and tested board, shipped without firmware. The complete golden firmware image (bootloader + ArduPilot + D-20C parameters in one file) and a step-by-step flashing guide are included in your downloads. Flashing takes a few minutes over USB-C (DFU) — no programmer or soldering needed.

All builds are also available as free downloads, installable any time via DFU. Setting up a VTOL flight controller has never been easier.

WHAT’S IN THE BOX

  • NavPack D04 — assembled and tested board, calibrated sensors, test protocol
  • Pre-installed firmware of your choice (Clear variant: firmware image + flashing guide in your downloads instead)
  • Silicone tube for the airspeed sensor
  • STL/3MF files for 3D printing — pitot-static system and NavPack mount

No cables or connectors included — none are needed.

3DFENSE — Navigation. Power. Launch. One board.

How it works

Download - Print - Assembly - Fly
  • 1
    Creating process of digital modelling

    Extensive hi-tech 3d structural reinforcement resulting in solid yet lightweight airframe thanks to additive 3Dprinting technology

  • 2
    Printing and testing

    Each plane has been thoroughly tested to find ideal shape and best possible inner structure

  • 3
    Distribution

    Choose your aircraft, download 3d files and print as many you need. Using your desktop 3Dprinter